I was then able to navigate to the setup files and install each of the three scanning components: ScanSnap Manager, ABBY FineReader for ScanSnap, and CardMinder, a utility for organizing business cards.Ī better solution is to download the PC software from the site, which will give you the latest versions of the software (I needed to download and install the new versions anyway because of a bug that was fixed after the installation disks were produced). I did find a workaround: from my computer drive list I used the context menu "Open" option to explore the DVD drive. The opening splash screen was completely inaccessible Window-Eyes couldn't read it at all. The Mac software installation was completely accessible, but Windows installation presented issues. Using the accompanying Abby Fine Reader is the easiest way to turn scans into text, though there is a way to port your scans to OpenBook, K1000 or other OCR packages (see below). The ScanSnap does not use standard TWAIN drivers, so you will need to use the Fujitsu drivers and software to create scanned images. Unfortunately, to download the Abby Fine Reader software, you will need your scanner's product and serial numbers, which are located in small type on the rear of the scanner base. Mac users will need to download the software from the product website. The ScanSnap SV600 Windows drivers and software come on a disk in the box, along with a copy of ABBY FineReader for ScanSnap. The mat has various markings to help users center the materials to be scanned, but I found this easy enough to do without visual cues, as there is also a notch at the center of the base to help with positioning. The black scanning mat unrolls to approximately 21 inches wide by 17 inches deep, with a 9-inch wide by 2-inch deep indentation that allows you to position the mat centered against the scanner. The unit I tested did have tape holding the scanner unit immobile inside the shell, which I needed to remove before using the scanner. There is no physical locking mechanism to hold the ScanSnap secure during transport. However, the ScanSnap also includes a bit of extra protection-two plastic end caps with adhesive edges that will secure the scanner to a surface. It would take a direct hit to knock it over. Start tilting the head so the light shines toward the center of the page, moving slowly until you have covered the entire sheet from top to bottom. Picture that desk lamp shining straight down at the edge of the paper closest to the base. The scanning unit, including the lights and lenses, snuggles beneath the shell and pivots up and forward. At its widest, the housing is 8 inches wide, and it is positioned above and just in front of the base. The scanner head has two components: the housing and the scanning unit with lens and a light bar. The neck holds the scan head about 11 inches from the desk top and is not adjustable. There are two buttons on the front: a long Scan button, and, just above it and not nearly so long, a Stop button. On the rear edge, toward the right, are two ports: the power cable port, at the extreme right, and a USB port to its left. The base is approximately 8.5 inches wide and 3 inches deep, and it sits at a tilt, about 1 ¾ inches high at the rear and ¾ inches high at the front. The ScanSnap SV600 resembles a large desk lamp, with a base, a neck, and a head that hangs over the text to be scanned. PC software (Mac software can be obtained via a download from the Fujitsu web site.).The ScanSnap employs a moving scanner head with light bar and scanning lens to scan downward, across pages and books that lay open on a table or desk. Often, the only way to get a truly useable scan is to destroy the book by cutting off its cover and spine-not a viable option if the book is a rental textbook or a library book.įujitsu took a new approach with its latest model, the ScanSnap SV600 Overhead Scanner. Scanning a book in this manner can also damage the spine, since you often have to flatten the book with some force in order to expose the inside edges of the text to the scanner. The process is tedious at best, requiring that you open the scanner lid, reposition the book, and close the lid for each new page or double-page spread you'd like to scan. I also use a flatbed scanner to recognize the texts of entire books, so I can read them on my computer or portable device. For years, I have used various flatbed scanners to perform optical character recognition (OCR) on memos, letters, and other documents, and to scan documents and photos for faxing or attaching to e-mails.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |